Looking for:
Manual sc300 |
Sc service | DocDroid.
Page 2 The information contained in this literature is subject to change without notice. Subject to the right to use its equipment, Eaton Corporation does not convey any right, title or interest in its intellectual property, including, without limitation, its patents, copyrights and know-how.
Page 5 Web Access Security All Rights Reserved. Page 6 SC Mappings Page 8: Sc System Controller Some configuration file changes can be made with the keypad, or all settings can be changed via a PC connected to the SC through a network or the USB interface see details on page It also allows real time data collection from building services and other external devices, and relay outputs for alarm signals or control of external devices.
From the Main Screen go directly to the Control Processes screen. From the Main Screen go directly to the Analogs screen. Page Main Menu Navigation At each menu screen press Enter to access the associated configuration menu screen s. See details on page Page Sub-Menu Tabs List of active alarms.
Alarm settings. LVD settings. Output boards. The Logon screen appears. Page Display Settings The functions of the navigations keys also change to suit the new display orientation. Either two large or three small parameters can be displayed. The default settings are two large parameters with the values Bus Voltage and Rectifier Current.
Parameter Description Where to find: System Page 24 Modified been changed from the last loaded configuration file. If the current configuration is corrupted for any reason, the SC will revert to this configuration. Then select Apply in the Changes window.
Page 27 The SC uses an internal lithium battery to keep the clock running while the SC is not powered up. Predicted life is at least three years. Life depends on the time the SC is not powered up, temperature, and battery age. Page Language Options Click on Next then follow the prompts to add the language. English is always available; other languages can be loaded as needed.
See Backup and Restore on page These will need to be re-entered. No control process can start until the ac supply is restored.
Page Float Voltage The system voltage is limited by maximum and minimum values. These values are not configurable by Web or DCTools. If these must be changed, contact your Eaton representative for access to ICE software. If an Engine Run Digital Input is available see below , then the SC uses this to determine if the generator is running.
If an Engine Run Digital Input is not available then the SC uses other values to determine if the generator is running. Page Battery Test The SC temporarily reduces the output voltage of the rectifiers to just below the bus voltage for a set duration. The battery then supplies power to the load.
A battery test passes if the battery voltage remains above a predetermined level for the duration of the test. Page Equalize Pending and it will start as soon as conditions allow.
Use Stop Equalize to cancel a Pending Equalize. Page Fast Charge Pending. Next Start Time The start time of the next scheduled Equalize. Page 40 Set the following parameters. Boost If this is enabled, the SC will set rectifiers elevated charge voltage until the Fast Charge Voltage is reached. The batteries will discharge into the load, while the rectifiers provide a backup if the battery fails.
Generally, the preference is for the load to be supplied from the alternative energy source first, and take energy from AC only when there is not enough solar or wind energy. Page 45 AC rectifiers. Page Rectifiers SC Handbook Rectifiers The SC registers all rectifier modules and solar chargers as they are inserted into the dc power system. Information The following information is available about rectifiers. Page 47 Rectifier manufacturer's model number. When this is set correctly, it enables the SC to assign a phase number to all rectifiers.
Page 50 The rectifier s will then resume normal operation. Page 52 Shutdown does not occur if shutting down a rectifier would push load percentage above High Threshold. Reset Run Times Sets the run time of all rectifiers to zero. Each channel can control one or more of up to 16 contactors, with coil voltages from 12V to 48V nominal. Page Typical Lvd Arrangements More complex arrangements with up to 16 contactors and a selection of disconnection criteria are possible with the SC system controller.
The exact arrangement s used in a particular Eaton dc power system will be described in the Installation and Operation Guide. See LVD Operation on page Page Alarms Alarms An SC supplied with a standard configuration file see details on page 23 has a standard set of alarms configured and enabled.
This will be sufficient for standard dc power system operation. For specific alarm arrangements all SC alarms can be individually enabled or disabled and are configurable. Projects French Manual. Projets Sign up for our newsletter Submit. Close Privacy Overview This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website.
We also use third-party cookies that help us analyze and understand how you use this website. This thing is mint!!! Under the hood is 3. Leather and sun roof It is a Lexus sc original 5speed. Has k miles and will go up because it is my daily. Car has all its maintenance records and has been well maintained. It has upgraded s brakes.
Unknown coilovers with 16 way adjustable d No mechanical issues, just couple of rust spots, worn drivers door hinge have a replacement one , r Needs engine work. Great potential in this build. Will need a tow. Feel free to message me with any questions. Really hard to find very low mileage sports coupe with 53, miles. In excellent condition, no accidents, beige interior cloth with not one stain.
Tires 5, miles ago. Clean title. Originally a California car. No sunroof.
No comments:
Post a Comment